Porta-Mole™ Underground Boring Machines are used to put pipe, cable or conduit under paved surfaces. Porta-Mole™ will bore 2' to 13' (5 to 33cm) in diameter and up to 200' (60m) in length in sand, clay and hard rock soil conditions. Porta-Mole™ also cleans Culvert Drains and Core Bores Curbs and Foundations. VW, 2 PIECE CASE, CRANKCASE BORING BAR. COMES AS SEEN, IN THE AD, WITH 2 SIZES OF PRESET CARBIDE CUTTERS.020' &.040', THE MOST COMMON OVERSIZES. THIS TOOL IS IN EXCELLENT WORKING CONDITION. THIS IS A SIMPLE, EASY TO USE TOOL. Freebie Road Side Tool Find! Pulled from Trash Pile. Portable engine cylinder boring machine, model FS by Kwik Way. Van Norman makes a similar machine. Portland Business Journal, September 2020: Founded in 1965, CLIMAX Portable Machine Tools makes port. October 27, 2020 The BB5000 Small Bore Kit LIVE Q&A on October 28, 2020.

• Porta Tool Boring Bar Bushings
• Porta Tool Align Boring Bars

Berco Small Boring Head

For Use with Berco ACP-151 and ACP-155 Bars
Boring Range 1.5' to 3.650'

Kwik Way Small Engine Boring Stand

Sunnen CK-2000 Midget Hone Head

Porta Tool Boring Bar Bushings

Peterson HC1DP Powerstroker Cylinder Hone

Friction Feed Hone Head
Uses Sunnen style AN hone stones
220 volt 3 phase

Kansas Instruments HC1DP Powerstroker

Friction Feed Hone Head
Uses Sunnen style AN hone stones
220 volt 3 phase
Located in Abilene TX

Peterson HC-1 Cylinder Hone Cabinet

inside dimensions - 30' x 50'
1/2 HP 110 volt
135 RPM
air assist stroke
Amp meter
30 gallon capacity

BHJ Small Block Chevy Honing Plate

Porta Tool Align Boring Bars

BHJ TORQUE PLATE CH-1-PM SBC

•Fits Chevrolet Small Block V8; Gen. I, Gen. II; 302-350, etc.
•4.090' Bore In Plate

BHJ Torque Plates for SBC

BHJ SBC Torque Plate CH-2CB

• Boring Bars for Negative 80º Diamond CNM_ Inserts (with or without coolant hole), SI-MCLN R/L
• Boring Bars for Negative 55º Diamond DNM_ Inserts (without coolant hole), SI-MDUN R/L
• Boring Bars for Negative 60º Triangular TNM_ Inserts, ST-MTUN R/L
• Boring Bars for Negative 35º Diamond VNM_ Inserts, SI-MVUN R/L
• Boring Bars for Negative 80º Trigon WNM_ Inserts (with or without coolant hole), SI-MWLN R/L
• Boring Bars for Positive 80º Diamond CCMT or CCGT Inserts SI-SCLC R/L
• Boring Bars for Positive 55º Diamond DCMT or DCGT Inserts SI-SDUC R/L
• Boring Bars for Positive 60º Triangular TCMT or TCGT Inserts SI-STUC R/L
• Boring Bars for Positive 35º Diamond VCMT or VCGT Inserts SI-SVUC R/L
• Boring Bars for Positive 80º Trigon WCMT or WCGT Inserts SI-SWUC R/L
• Positive 15 Degree End Cutting Edge Angle Boring Bar`
• Boring Bars for Triangular TPU Inserts (right hand only) SI-CTUPR
• Boring Bars for Positive 80º Diamond CCMT or CCGT Inserts SI-SCLCR